Isspro R8480-SET Bedienungsanleitung PDF herunterladen

ISSPRO, INC. 2515 N.E. Riverside Way, Portland OR 97211

Telephone: (503) 288-4488  Toll Free: (800) 888-8065

FAX: (503) 249-2999

Form IS129 (Rev D 2/15/06) Page 1 of 7

ISSPRO 3 3/8” Diameter Programmable Speedometer

Microprocessor Aircore Version

General Information:

Operating Voltage: 11 – 32 VDC. Note: Instrument comes equipped with a 12V lamp. Replace with

one of proper voltage when installing instrument on 24V systems. 24V Lamp Part

number is 656.

Input: Magnetic sensor or AC generator

Transient Protection: +100 V, -400 V

Reverse Voltage Protected

Calibration:

The ISSPRO Programmable Speedometer is calibrated (programmed) by setting a combination of ten switches

found in the rear of the instrument. The odometer and pointer are electronically linked together and both are

calibrated when the switches are properly set. Program before installing.

Note: the switch setting must be done with power “off”. If power is left “on”, changing the switch will have no

effect on calibration until power is interrupted.

Calibration Procedure:

Calculate the "calibration number" from the appropriate formula below. (A minimum calibration number of 10080

is required to be within calibration range). Refer to the "CALIBRATION SWITCH SETTING" table with this

number. Locate the row in which the calibration number is between the limits, then set the switches marked with a

"0" to the "on" position (up).

Example: Calibration number = 29644: From the table 29644 lies between 29581 and 29700, therefore, switches

4, 9, and 10 will be set to "on".

Note: “0” means switch is on, “1” means switch

is off.

(1) Front wheel mounted tone wheel:

Calibration Number = Number of Slots in Tone

Wheel X Tire Revs per Mile

(2) Tail Shaft mounted magnetic sensor:

Calibration Number = Tire Revs per Mile X

Differential Ratio X 16

(3) Sender driven from transmission cable drive:

Calibration Number = Cable Turns Per Mile X

Number of Pulses per Sender Turn

Note: For metric versions, substitute kilometers for miles in the above formulas. Multiply the resulting value by

1.621 to obtain final calibration number.

Slot

Lamp & Socket

(Remove CCW)

Calibration Switches

Rear View of Speedometer

1 2 3 4 5 6 7 8

Inhaltsverzeichnis

Seite 1 - Rear View of Speedometer

ISSPRO, INC. 2515 N.E. Riverside Way, Portland OR 97211 Telephone: (503) 288-4488  Toll Free: (800) 888-8065 FAX: (503) 249-2999 Form IS129 (Rev

Seite 2

Form IS129 (Rev D 2/15/06) Page 2 of 7 If the number of cable turns per mile (or kilometer) is not known, follow this procedure: Obtain a ratio tes

Seite 3

Freq at 60MPHFreq at 60MPHFreq at 60MPHFrom To 1 2 345678910 From To 12345678910 From To 1234567891010080 10140 X X X X X X X 168 17701 17820 X X X X

Seite 4

Freq at 60MPHFreq at 60MPHFreq at 60MPHFrom To 1 2 345678910 From To 12345678910 From To 12345678910Note that "X" is Switch ONCalibration Sw

Seite 5

Freq at 60MPHFreq at 60MPHFreq at 60MPHFrom To 1 2 345678910 From To 12345678910 From To 12345678910Note that "X" is Switch ONCalibration Sw

Seite 6

Freq at 60MPHFreq at 60MPHFreq at 60MPHFrom To 1 2 345678910 From To 12345678910 From To 12345678910Note that "X" is Switch ONCalibration Sw

Seite 7

Freq at 60MPHFreq at 60MPHFreq at 60MPHFrom To 1 2 345678910 From To 12345678910 From To 12345678910Note that "X" is Switch ONCalibration Sw

Seite 8 - Diagram is not actual size

ISSPRO, INC. 2515 N.E. Riverside Way, Portland OR 97211 Telephone: (503) 288-4488  Toll Free: (800) 888-8065 FAX: (503) 249-2999 Form IS118 (Rev D

Kommentare zu diesen Handbüchern

Keine Kommentare

Isspro R8480-SET Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Hardware Isspro R8480-SET herunter. ISSPRO R8480-SET User Manual [en] Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Isspro R8480-SET